Questions? Call 1-386-586-3650

Keyless Entry Verification Procedure for Toyota 4Runner 2001

Dealer Installed System:
Perform the following test to see if you have this system:
Start with the following conditions:Â
Key is out of the ignition
Driver door is open (all other doors are closed)
Driver door is unlocked (other door locks don’t matter).
Insert the key into the ignition (don’t turn it) and pull it out.
Perform these steps within 40 seconds:
Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock.  A lock/unlock cycle consists of pressing the power lock switch, followed by pressing the power unlock switch on the driver’s door panel.  Use an even pace and try to go relatively fast.
Close, then open the driver’s door.
Perform these steps within 40 seconds:
Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock (just as you did previously).Â
Insert Key in ignition.
Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
Remove the key from the ignition.
Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode.  Return to Step 1 if the locks do not cycle at this point.
 
Factory Installed System:
Perform the following test to see if you have this system:
Start with the following conditions:
Key is out of the ignition
Driver door is open (all other doors are closed)
Driver door is unlocked (other door locks don’t matter).
Insert the key into the ignition (don’t turn it) and pull it out.
Perform these steps within 40 seconds:
Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock.  A lock/unlock cycle consists of pressing the power lock switch, followed by pressing the power unlock switch on the driver’s door panel.  Use an even pace and try to go relatively fast.
Close, then open the drivers door.
Perform these steps within 40 seconds:
Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock (just as you did previously).
Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
Remove the key from the ignition.
Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating you have the factory keyless entry system.

 


 


  
Factory Keyless Entry 4 Button Remote HYQ12BAN HYQ12BBX 89742-35050
Factory Keyless Entry 4 Button Remote HYQ12BAN HYQ12BBX 89742-35050

Originally Toyota made this remote with an FCC ID of HYQ1512Y and a part number of 89742-35021.  Toyota discontinued that version and superceded with these numbers: 89742-0C010, 89742-35040, 89742-0C030.  Toyota seems to have settled on

From: $45.00 View Product
Replacement Case and Button Pad Shell Housing HYQ12BBX HYQ12BAN HYQ1512Y 4 Button with RearGlass
Replacement Case and Button Pad Shell Housing HYQ12BBX HYQ12BAN HYQ1512Y 4 Button with RearGlass

A quick, easy and affordable way to replace a cracked or worn out keyless entry remote key fob case or shell. Replace the outer case or shell instead of the entire assembly with this product. Installation is simple and reprogramming is not required.

From: $7.95 View Product
Toyota Dealer Installed Keyless Entry Remote BAB237131-056 08191-00922 3 Button RS3200 VIP
Toyota Dealer Installed Keyless Entry Remote BAB237131-056 08191-00922 3 Button RS3200 VIP

This is a replacement for Toyota Part Number 08191-00922 and FCC ID BAB237131-056.  Remote is tested on a keyless entry tester for radio signal strength, battery strength, and proper functioning before shipping to you.  Works on: 2000-20

From: $50.00 View Product
TEASoftware