50104.952
Toyota Factory Keyless Entry Remote HYQ12BAN HYQ12BBX 89742-42120 3 ButtonRemote Tested Before Shipping, Guaranteed To Work
This is a replacement for Toyota Part Numbers 89742-20200, 89742-0C020, 89742-42120 and FCC ID HYQ12BAN or HYQ12BBX with 3 buttons. Remote is tested on a keyless entry tester for radio signal strength, battery strength, and proper functioning before shipping to you.  This works on: 2004
ToyotaFactory Keyless Entry Remote 89742-4212
4.833333015441896
(6) Show Reviews

Toyota Factory Keyless Entry Remote HYQ12BAN HYQ12BBX 89742-42120 3 Button

Remote Tested Before Shipping, Guaranteed To Work

Price: $50.00 - $104.95
Select Your Vehicle
Specifications
Item Specifications
Product Type
Regular Remote
Remote Programming
Onboard
RF Transmission
1Way
Frequency
315 MHz
LED
None
Buttons
3
Description

This is a replacement for Toyota Part Numbers 89742-20200, 89742-0C020, 89742-42120 and FCC ID HYQ12BAN or HYQ12BBX with 3 buttons. Remote is tested on a keyless entry tester for radio signal strength, battery strength, and proper functioning before shipping to you.  This works on: 2004-2005 Toyota Celica, 2004-2005 Toyota Echo, 2007-2008 FJ Cruiser,
2001-2007 Toyota Highlander, 2001-2003 Toyota Prius, 2001-2003 Toyota RAV-4 (Factory installed system), 2004-2005 Toyota Rav-4, 2004-2005 Toyota Tundra, 2006 Toyota Tundra (Double Cab and Single Cab).


PROGRAMMING INSTRUCTIONS (04-05 Celica, 04-05 Echo, 01 and 03 Highlander, 01-03 Prius, 02-03 Rav-4, 05 Tundra:)

1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other doors don’t matter).

2. Perform the next two steps within 5 seconds:
a. Insert the key into the ignition (don’t turn it) and pull it out.
b. Insert the key into the ignition (don’t turn it) and pull it out.

3. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition (don’t turn it) and pull it out.

4. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition.
d. Close the driver’s door.
e. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
f. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:
a. Press the lock and unlock buttons on the transmitter simultaneously for 1 second.
b. Immediately after releasing the lock and unlock buttons, press the unlock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.

7. Open driver’s door.


PROGRAMMING INSTRUCTIONS (04 Tundra:)

1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other door locks don’t matter).

2. Insert the key into the ignition (don’t turn it) and pull it out.

3. Perform these steps within 40 seconds:
a. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock. A lock/unlock cycle consists of pressing the power lock switch, followed by pressing the power unlock switch on the driver’s door panel. Use an even pace and try to go relatively fast.
b. Close, then open the drivers door.

4. Perform these steps within 40 seconds:
a. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock (just as you did previously).
b. Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
c. Turn the ignition to ON (as far as you can go without cranking your engine), then back to OFF.
d. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:
a. Press the LOCK and UNLOCK buttons on the first transmitter simultaneously for 1 second and release.
b. Immediately after letting go of the LOCK and UNLOCK buttons, press the UNLOCK button by itself and release. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks don’t cycle, or cycle twice, repeat steps 6a and 6b as the remote has not been accepted.
c. Repeat steps 6a and 6b for each transmitter that will operate the vehicle, including any old transmitters.

7. Close driver door.


PROGRAMMING INSTRUCTIONS (02 and 04-05 Highlander, 01 Rav-4:)

1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other doors don’t matter).

2. Perform the next two steps within 5 seconds:
a. Insert the key into the ignition (don’t turn it) and pull it out.
b. Insert the key into the ignition (don’t turn it) and pull it out.

3. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition (don’t turn it) and pull it out.

4. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Close the driver’s door.
d. Insert the key into the ignition.
e. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
f. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:
a. Press the lock and unlock buttons on the transmitter simultaneously for 1 second and release.
b. Immediately after releasing the lock and unlock buttons, press the lock button by itself and release. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.
c. Within 40 seconds, repeat steps 6a and 6b for each additional transmitter.

7. Open driver’s door.


PROGRAMMING INSTRUCTIONS (04-05 Rav-4:)

1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other doors don’t matter).

2. Perform the next two steps within 5 seconds:
a. Insert the key into the ignition (don’t turn it) and pull it out.
b. Insert the key into the ignition (don’t turn it) and pull it out.

3. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition (don’t turn it) and pull it out.

4. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Close the driver’s door.
d. Insert the key into the ignition.
e. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
f. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:
a. Press the lock and unlock buttons on the transmitter simultaneously for 1 second and release.
b. Immediately after releasing the lock and unlock buttons, press the unlock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.
c. Within 40 seconds, repeat steps 6a and 6b for each additional transmitter.

7. Open driver’s door.


PROGRAMMING INSTRUCTIONS (06-07 FJ Cruiser, 06-07 Highlander:)

1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other doors don’t matter).

2. Perform the next two steps within 5 seconds:
a. Insert the key into the ignition (don’t turn it) and pull it out.
b. Insert the key into the ignition (don’t turn it) and pull it out.

3. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition (don’t turn it) and pull it out.

4. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Close the driver’s door.
d. Insert the key into the ignition.
e. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
f. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:
a. Press the lock and unlock buttons on the transmitter simultaneously for 1 second and release.
b. Immediately after releasing the lock and unlock buttons, press the lock button by itself and release. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.

7.  Open driver’s door.


PROGRAMMING INSTRUCTIONS (06 Tundra Double Cab:)

1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is OPEN (all other doors are closed).
c. Driver door is unlocked.

2. Insert the key into the ignition (don’t turn it) and pull it out.
3. Perform these steps within 40 seconds:
a. Using the power lock/unlock switch on the driver’s door, perform 5 lock/unlock cycles starting with lock. A lock/unlock cycle consists of pressing the power lock switch, followed by pressing the power unlock switch on the driver’s door panel. Use an even pace and try to go relatively fast.
b. Close then open the driver’s door.

4. Perform these steps within 40 seconds:
a. Perform 5 lock/unlock cycles again with the switch on the driver’s door starting with lock.
b. Insert the key in the ignition cylinder.
c. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
d. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:
a. Press the LOCK and UNLOCK buttons on the transmitter simultaneously for 1 second and release.
b. Immediately after letting go of the lock and unlock buttons, press the UNLOCK button by itself and release. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice (two lock and unlock cycles), this means your remote has not been accepted. Repeat steps 6a and 6b until the door locks cycle only once.
c. Repeat steps 6a and 6b for each remote including old ones.

7. Close the driver’s door.

PROGRAMMING INSTRUCTIONS (06 Tundra Single Cab:)

1. Start with the following conditions:
a. Key is out of the ignition
b. Driver door is open (all other doors are closed)
c. Driver door is unlocked (other doors don’t matter).

2. Perform the next two steps within 5 seconds:
a. Insert the key into the ignition (don’t turn it) and pull it out.
b. Insert the key into the ignition (don’t turn it) and pull it out.

3. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition (don’t turn it) and pull it out.

4. Perform these steps within 40 seconds:
a. Close then open the driver’s door.
b. Close then open the driver’s door.
c. Insert the key into the ignition.
d. Close the driver’s door.
e. Turn the ignition to ON (as far as you can go without cranking your engine) then back to OFF.
f. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should cycle (lock then unlock) automatically indicating successful entry into programming mode. Return to Step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:
a. Press the lock and unlock buttons on the transmitter simultaneously for 1 second.
b. Immediately after releasing the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle (lock then unlock) once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b for this remote as it has not been accepted.
c. Repeat steps A and B for each new remote.

7. Open driver’s door.

  • Free Tech Support
  • Battery Included
  • Guaranteed To Work
  • Tested Before Shipping
  • For more questions about this product, please Contact Us
Application List
ImageSKU / Part NoApplicationDetailPriceAdd to Cart
4245A 4245AToyota Celica (2004-2005)$50.00BUY
+ -
4245A-OEM 4245A-OEMToyota Celica (2004-2005)$104.95BUY
+ -
4245A 4245AToyota Echo (2004-2005)$50.00BUY
+ -
4245A-OEM 4245A-OEMToyota Echo (2004-2005)$104.95BUY
+ -
4245A 4245AToyota FJ Cruiser (2007-2008)$50.00BUY
+ -
4245A-OEM 4245A-OEMToyota FJ Cruiser (2007-2008)$104.95BUY
+ -
4245A 4245AToyota Highlander (2001-2007)$50.00BUY
+ -
4245A-OEM 4245A-OEMToyota Highlander (2001-2007)$104.95BUY
+ -
4245A 4245AToyota Prius (2001-2003)$50.00BUY
+ -
4245A-OEM 4245A-OEMToyota Prius (2001-2003)$104.95BUY
+ -
4245A 4245AToyota RAV4 (2001-2003)$50.00BUY
+ -
4245A-OEM 4245A-OEMToyota RAV4 (2001-2003)$104.95BUY
+ -
4245A 4245AToyota RAV4 (2004-2005)$50.00BUY
+ -
4245A-OEM 4245A-OEMToyota RAV4 (2004-2005)$104.95BUY
+ -
4245A 4245AToyota Tundra (2004-2005)$50.00BUY
+ -
4245A-OEM 4245A-OEMToyota Tundra (2004-2005)$104.95BUY
+ -
4245A 4245AToyota Tundra (2006)$50.00BUY
+ -
4245A-OEM 4245A-OEMToyota Tundra (2006)$104.95BUY
+ -
You might be interested in these items
Return Policy

OVERVIEW

At RAK we make returns as easy as possible. Our mission is to provide you with the best products and the best service in the industry. We understand that sometimes, customers change their minds about products that they order or simply do not need them anymore. We also know that customers are cautious about Return Policies since they are often tricky and misleading. Our goal is to make the return or exchange process trustworthy and as simple as 1-2-3.

RETURN POLICY

If for any reason you are not completely satisfied with your purchase, you may return the item within 30 days of delivery of your order.

The following rules apply:

  • Products must be in the same condition we sent it in.
  • Shipping Fees are non-refundable.
  • All returns must be made by signing in, going to MY ACCOUNT, clicking order history, finding the order, click Return this item.There are few non-returnable products & services that may be offered on our website. It will indicate clearly in the product description if a different return policy applies.
  • Order cancellations can only be requested prior to shipment.

RETURN PROCEDURE

To return a product, you must first request a Return Merchandise Authorization (RMA) that is located in the MY ACCOUNT section next to each order item that you want to return.

EXCHANGE PROCEDURE

There are 2 ways you can go about exchanging a product:

  • Option 1 (Slower) - Use the standard return procedure to request an RMA for the part you need exchanged. In your request please specify the exact item(s) you would like to exchange to. Upon receipt of your returned product we will process an exchange and ship the new part. If there is a difference in the price, you will be either refunded or charged the difference.
  • Option 2 (Faster) - Order the new part over the phone and request to include a prepaid label to send back the first purchase for refund.

DEFECTIVE, DAMAGED, OR INCORRECT PRODUCTS

We all know that accidents happen sometimes. If your product(s) will arrive defective, damaged, or simply incorrect, please contact our customer service department as soon as possible. Please do not attempt to use or install the part! We will send you a replacement part and provide you with a prepaid return label to return the defective part. Product(s) must be returned to us within 30 days. If the damage was caused by a shipping courier, we will schedule a damage pick up by the courier.

ORDER CANCELLATIONS

When you request a cancellation of an order or a part it may take up to 24 business hours to process your cancellation claim. This process may involve voiding orders in computer systems, removing items from backorder logs, having operations personnel pull items from production schedules and sometimes stopping orders at the shipping dock. Also note that sometimes products ship more quickly than expected, so we recommend that you do not purchase alternative products until receiving final confirmation of your cancellation.

REFUNDS & CREDITS

After we accept your return, you will be issued a refund via the same payment method as you had originally used to place the order. The refund amount will be composed of the original purchase price minus shipping charges. You will be sent an email confirming receipt of the return and your credit. Please allow an additional 5-7 days for the credit to appear on your account.

Customer Reviews
Share your thoughts with other customers
Login to leave a review
Top Reviews
Thank you.
by Valued Customer on September 01, 2009
 
 
 
 
 
Verified Purchase

I received my order within a week and it works perfectly.

Was this review helpful to you? yes no
Greetings Jason
by Valued Customer on February 18, 2009
 
 
 
 
 
Verified Purchase

"I am writing to thank you for your service and quality product. The directions worked perfectly and I was able to program it within a few minutes. When confronted with what the dealer wanted, I succumbed to the fact I would just do without. Then I decided to look for an alternative and found your site. I will happily recommend you to anyone looking to replace their remote or key. Thank You,"

Was this review helpful to you? yes no
All is well
by Valued Customer on June 23, 2016
 
 
 
 
 
Verified Purchase

I was sent the incorrect FOB first, though it was rectified very quickly.

Was this review helpful to you? yes no
Thanks
by Valued Customer on July 30, 2009
 
 
 
 
 
Verified Purchase

I was outraged when my Toyota dealer asked $160 plus an additional programming charge to replace my remote key that cost $35 when I bought my Highlander in 2003*. I'm thrilled that you offered the remote at a reasonable price, and the programming worked perfectly at the second attempt. The remote works at least as good as my previous remotes. Delivery was prompt, and the programming instructions were clear.

Was this review helpful to you? yes no
Hi Nikkie,
by Valued Customer on November 02, 2011
 
 
 
 
 
Verified Purchase

Jay got together with the 2006 Toyota Tundra yesterday and got the remote programmed. I can't believe that vehicle required a 2003 remote. Anyway I wanted to let you know the outcome and thank you profusely for helping us figure this out. Thank you for being patient and prudent about finding the right remote!

Was this review helpful to you? yes no
just received my order
by Valued Customer on February 26, 2009
 
 
 
 
 
Verified Purchase

Excellent delivery time, excellent programming instructions, and it works fine ! Thank You.

Was this review helpful to you? yes no
See more reviews
Questions & Answers
Don't see what you're looking for?

A

If you have any questions please contact us via Live Chat or call 386-586-3650. You can also send a text message (SMS) to 386-586-3650.

By Michael B on June 16, 2017. 
Was this review helpful to you? yes no
A

Yes, as long as programming is done properly.

By Charles R on September 19, 2017. 
Was this review helpful to you? yes no
A

Our specials, coupons, and discounts are constantly revolving. Visit this page for the active deals: https://www.remotesandkeys.com/specials

By Ernesto C on December 07, 2017. 
Was this review helpful to you? yes no
A

Visit this troubleshooting blog: https://www.remotesandkeys.com/blog/troubleshooting

By Forsythia M on December 12, 2017. 
Was this review helpful to you? yes no
A

There are two possible reasons to not see an add to cart button: 1) You haven't made the required choices in dropdowns or buttons near the price. 2) There could be a quote button instead of add to cart if a product is out of stock or if we need to double check availability before placing an order.

By Dave G on December 16, 2017. 
Was this review helpful to you? yes no
See more answered questions

Remotes And Keys is the premier provider of replacement automotive keyless entry remote transmitters, keyfobs, transponder keys, and accessories. We take pride in the quality of our inventory and the amazing people we work with. Feel free to drop us a question or say hi!

SIGN UP FOR OUR NEWSLETTER
and receive special deals and discounts.

CONTACTS

Remotes And Keys
PO Box 290079
Brooklyn, NY 11229

Phone: 386-586-3650
Fax: 718-228-8876

TEASoftware