Extended warranty is available on the checkout page.
When there aren't 2 working Smart Key Remote to use to initiate programming, an automotive locksmith is required for programming. But if you have two Smart Key Remotes that are already working with the vehicle, this can be programmed using an easy to follow customer programming procedure. However, some vehicles that use this remote would require a locksmith.
Remote For Lincoln:
Factory Keyless Entry Smart Key transmitter with FCC ID M3N5WY8609. 4 more key fobs have the same fcc id.
The Ford part number is 164-R8094 or BA1T-15K601-AX.
The Strattec part number is 5921288.
This is a 1Way remote which sends it's signals on a frequency of 315 MHz. This remote has 5 buttons, tested and guaranteed to work.
Programming Procedure:
Your vehicle isn't onboard programmable and would need key cutting, please contact an automotive locksmith to program the vehicle to accept the replacement remote or key or to cut a key. Please use an automotive locksmith rather than the dealer. You are likely to get a better service for a more reasonable price. An automotive locksmith will program your new remotes or keys by hooking up an expensive scan tool to your vehicle?? computer and making the vehicle learn the new remotes or keys.
- For 2013-2019 MKT and 2013-2016 MKS:
You must have two previously programmed intelligent access keys inside the vehicle and the new un-programmed intelligent access keys readily accessible. If two previously programmed keys are not available, you must take your vehicle to your authorized dealer to have the spare key(s) programmed. Ensure that the vehicle is off before beginning this procedure. Ensure that all doors are closed before beginning this procedure and that all doors remain closed throughout the procedure. Perform this procedure exactly as described below, and perform all steps within 30 seconds of starting the sequence. If any steps are performed out of sequence, stop and wait at least one minute before starting again. Please read and understand the entire procedure before you begin.
1. Place the new un-programmed intelligent access key in the pocket inside the center console utility compartment.
2. Press the driver or passenger power door unlock control three times.
3. Press and release the brake pedal one time.
4. Press the driver or passenger power door lock control three times.
5. Press and release the brake pedal one time. The indicator on the Start/Stop button should begin to rapidly flash, indicating that the programming mode has been entered and two programmed intelligent access keys have been detected in the vehicle.
6. Within one minute, press the start/stop button. A message will be displayed on the message center indicating that the new Intelligent Access Key was programmed. If four intelligent access keys have already been programmed to your vehicle, you cannot program anymore and the message. MAX # OF KEYS LEARNED will be displayed on the message center.
7. Remove Intelligent Access Key from utility compartment pocket and press the unlock or lock control on the newly programmed intelligent access keys to exit programming mode.
8. Verify that the remote entry functions operate (lock, unlock) and that the vehicle starts with new Intelligent Access Key. If the Intelligent Access Key has been successfully programmed, it can be used to activate the Intelligent Access with Push Button Start feature and can be used to start your vehicle.
You must have two previously programmed intelligent access keys inside the vehicle and the new un-programmed intelligent access keys readily accessible. You must take your new un-programmed intelligent access key if two previously programmed remotes are not available. Ensure that the vehicle is OFF, all doors are closed and all doors remain closed throughout the procedure. Perform the steps exactly described below and within 30 seconds of starting sequence. If any steps are performed out of sequence, stop and wait at least one minute before doing it again.
Please read and understand the entire procedure before you begin.
1. Place the new un-programmed intelligent access key in the pocket inside the center console utility compartment.
2. Press the driver or passenger power door unlock control three times.
3. Press and release the brake pedal one time.
4. Press the driver or passenger power door lock control three times.
5. Press and release the brake pedal one time. The indicator on the Start/Stop button should begin to rapidly flash, indication that the programming mode has been successfully activated and two previously programmed remotes have been detected in the vehicle.
6. Within one minute, press the start/stop button. A message will be displayed on the message center indicating that the new Intelligent Access Key was programmed.
7. Remove the Intelligent Access Key from utility compartment pocket and press the unlock or lock control on the newly programmed intelligent access keys to exit programming mode.
8. Verify that the remote entry functions operate (lock, unlock) and that the vehicle starts with new Intelligent Access Key.
The following vehicles can use this remote when equipped with the factory keyless entry system:
Lincoln Navigator (2015-2017), Lincoln MKS (2013-2016), Lincoln MKT (2013-2019), Lincoln MKX (2011-2015).